Six Stage Opto FET VCF New filter module in which so-called opto FETs are used to control the filter frequency, Dimensions (W x D): 40.3 mm (8 HP) x 65 mm, Power requirement: 40 mA
Wasp Filter Special edition, Special 12 dB multimode filter, Circuit technology of the "EDP Wasp", Black front, Yellow pot caps, Width: 8 HP, Depth: 45 mm, Power requirements: +30 mA (+12 V)/-10 mA (-12 V)'
USB to Clock / Start / Stop Interface Synchronization of clock-controlled modules via MIDI and USB, MIDI input, USB input for MIDI via USB, Clock outputs, Wait button / control input, LED indicators for Clock, "1" and...'
Case for Modules A number with 84 HP for installation of modules, Incl. external power supply (1200 mA) and bus board, Dimensions (W x H x D): approx. 445 x 150 x 160 mm
Precision Adder / Buffer 4 CV inputs (1x with controller, 3x without controllers), Width: 6 TE / HP, Depth: 50 mm, Power requirement: +10 mA (+12 V) / -10 mA (-12 V)
Passive Multi-Port Distributor 8x Interconnected jacks, Sockets are divided into 2x quadruple groups- but can also be modified to an eight-multiple (soldering bridge on the circuit board), Width: 2HP
Dual CV/ Gate to MIDI/ USB Interface Two independent CV/ Gate-to-MIDI/ USB interfaces, Each interface with 4 inputs (Gate, CVN, CVV, CVC), MIDI in/ out, USB, Euro rack format, Width: 10 HP, Depth: 55 mm, Power...
S-Trigger Cable With built-in S-trigger electronics, Length: 1.2 m, 3.5 mm Mono mini jack plug to 1/4" mono jack, Converts gate to switched trigger (S-trigger)'
External Foot Controller Module Foot controller connector and dual foot switch connector to provide analogue control voltages (foot controller) and two gate / trigger signals (footswitches) to control other A-100...
Gate / Trigger Combiner Simple, passive module that combines up to 7 gate, trigger or analog signals, Eurorack format, Width: 4 HP, Depth: 20 mm, Power Requirement: + 0mA (+ 12V) / -0mA (-12V)
USB/MIDI-CV/Gate Interface Allows the integration of the A-100 module system into a USB or MIDI system, 4 Analogue CVs, Gate signal, Width: 6 HP, Depth: 55 mm, Power consumption: + 12V: 60mA/ -12V: 10mA
Tapped BBD Module 6 Outputs (BBD stages 396, 662, 1194, 1726, 2790, 3328), Two mixing units each with dry/ wet knobs, Width: 30 HP, Depth: 70 mm, Power consumption: +120 mA (+12V) / -50 mA (-12V)
Cable Set For DIY Synthesizer kit, Consisting of two 16-pin and five 10-pin flat-ribbon cables, With matching counterparts to the 2-pin contact strips on the DIY Synth board, Length: Each 50 cm, The other end of each...
Filter 12 dB Multi-mode filter, in which the circuit of the SEM module is used, Width: 8HP 40.3 mm, Depth: 55 mm (measured from the rear of the front panel), Power requirements: +30 MA (+ 12V) / -20 mA (-12V)
Quad Exponential VCA / Mixer The module A-132-4 contains four identical voltage-controlled amplifiers (VCA) with exponential normalization. Each VCA has two control voltage inputs (CV1, CV2), a signal input (In), and a...
Dual Attenuator Passive attenuator, Level attenuation for voltage controls or audio signals for A-100 modules or modules from other manufacturers without attenuators
DC amplifier module Simple amplifier, Is suitable for control voltages and audio signals via DC coupling, Selectable maximum amplification: 1, 2 or 4 (switchable), Level controls, 2 Peak LEDs, Eurorack format, Width: 4...
Midi-to-CV/ Gate Interface Output control voltage: 0 - 5V, Portamento time adjustable via glide knob, Width: 6 HP, Depth: 45 mm, Power consumption: +50 mA (+12V)/ -20 mA (-12V)
Multiple Distribution Module Passive, Each socket can be switched in 3 variants (1,2, off), 8-Way multipin: all switches on the left or right, Two times 4-fold multipin: four on 1, four on 2, Eurorack format, Width: 6...
Multimode Filter For Doepfer modular systems, Over 15 different filter types, 8 filters are available at the same time, Width: 12 HP / 60.6 mm, Depth: 50 mm (measured from the back of the front panel), Power...